9 Tips On How to Get Your Beats or Songs Sound Clean and Loud

Source: pexels.com

After creating a song, you need editing to make them sound clear and loud. There is no use in developing music when you do not have an audience to listen to your song. Every person loves perfect songs with proper tuning and clear sound.

It takes a lot of time and effort to make a song better. A singer must sing a song that is compatible with the music, and hence, everything seems perfect before presenting it in front of the audience.

Read more to get free beats by following some simple steps. It is possible to make your song better by making the sound clear and loud. You can compare the licensing options and choose the best option as per your needs.

If you are working hard to make the beats clear, then you are making some mistakes. In the following write-up, we will discuss how to get your songs or beats to make the sound clean and loud with some tips.

1. Use High-quality Sounds

Source: pexels.com

You can enhance the quality of the mix by choosing high-quality samples or sounds. This one is quite a standard case with drums. There are chances of getting messy sounds through which one cannot achieve the loud mix.

Ensure that you set up a peaceful environment to determine good-quality sound and make it crisp and clean. You have to focus and listen to the beats carefully to make it in the way you like. You can find some trusted sources to get better sounds and use them for layering.

2. Learning Compression

You have to learn compression instead of using it. Many individuals think that compression can make the sound loud, but it can harm your song better than before. It is necessary to have enough experience to deal with compression settings.

You have to give some time to experiment with it and learn more about the differences in every setting. You must understand the dynamics before you implement them. If you are focussing on loudness, then it is better to focus on parallel compression and multiband.

3. Saturation

Source: musicianonamission.com

It is possible to make every channel loud by separating and saturating them. There is another way, i.e., grouping those channels and making them go into the mix bus. It is necessary to learn and master this process to get better output. You must experiment to get the best beats out of different types of saturation.

This process works well on drum beats but makes sure that you try various plugins to get different results. There are chances of getting distortion if you do not take it carefully. Therefore, you should listen to the beats carefully and make changes slowly.

4. Creating Room in the Mix

If you want to make a song clean and loud, then you have to focus on various elements like frequency, balance, etc., instead of working with clean samples.

You can use EQ to make some spaces in your sounds. You have to set the frequency and maintain the balance in the mix. Creating a room is relatively necessary for the mix to make the beats sound clean and loud.

5. Bass Settings

Source: pexels.com

You have to put a lot of effort while dealing with bass settings. If you do not make the settings correctly, then it can affect the loudness. You can use a spectrum analyzer to check the low end and determine whether you are making the proper settings. Your song may sound slow because it may have low frequencies.

It is necessary to remove the bass frequencies set at low. When you remove those settings, the sound becomes loud and clear. You have to make it up and down to know the proper settings. You may need to change compressor settings to get better output.

6. Using the Right Limiter

There are different types of limiters, and you can get different outputs in each case. Start pushing it to see what results you are getting. There are chances of getting distortion, but you have to make slight changes to see whether you are getting the desired results.

7. Multiband Limiting

Source: reasonstudios.com

The process of multiband limiting was introduced in recent years. It helps in managing the sound loudness and makes it correct. It can squeeze the additional dB and loud beats of the mix.

On the other side, it can be relatively destructive, and you have to be careful while dealing with it. There are possibilities of losing integrity, and therefore, go ahead slowly and make changes.

8. Avoid Overdoing the Limiting Process

The limiting process is done to correct the loudness of any song. These limiters can affect your beats and make them worse than better, and you can observe a detrimental effect on your audio.

Instead of controlling the loudness, you can make the beats extremely loud, which seems unsuitable for many listeners. Therefore, it is advisable not to overdo the compression process because, in this way, you are overdoing the limiting process.

9. Use of Low Ratios and Avoiding Attack Times

There is a specific rule of compression that one must follow, and it appears in ratio, i.e., 4:1 or 1.5:1. If you are exceeding the 4:1, then you are limiting more than expected. If you increase the ratio, it will also increase the threshold. Avoid over-compression, and you can control it by following the proper ratio.

The Bottom Line

Editing a song can be a complicated task, in which you have to make the beat sound loud and clean. You must follow all the mentioned tips to improve the quality of the audio safely. You must follow the guidelines because these tools can be destructive and hence, ruin the quality severely.

Make sure that you make the changes slowly that are easy to control. Whenever you make any setting, create copies and work on them. The process of making the sound clean and loud is not complicated until you learn various strategies. Therefore, you must get enough experience to deal with these tools and settings.

LEAVE A REPLY

Please enter your comment!
Please enter your name here